Machine operator Jobs

Job description:<br><br>JOB PURPOSE:To ensure the smooth and continuous operation of the gas and steam turbines, HRSGs, potline rectifiers, associated plant equipment and all related utility services in his designated area of responsibility, in a safe and efficient manner as instructed by the Shift Supervisor or the Main Control Room Operator. KEY ACCOUNTABILITIES:Ensure that all plant and equipment under his control are operated in a safe and efficient manner. Ensure that all instructions are carried out promptly and efficiently. Record routine parameter readings on regular basis and report deviations. Inform the Supervisor (or) control room of any abnormalities/problems on equipment Ensure standby equipment is readily available for service in an emergency. Assist in carrying out routine testing/re-commissioning of plant after maintenance outages. Adopt safe working practices to ensure personal and plant safety. Identify hazards and participate effectively in reporting system. Maintain good standards of housekeeping. Must be fully conversant with all emergency procedures related to the equipment in his designated area of responsibility Carry out on the job training Strive to achieve increased competency Jebel Ali Site, additional roles Operator Turbine & Boiler Assistant Operator At Jebel Ali Site, for the roles of Operator Turbine & Boiler and Assistant Operator, the above accountabilities will be restricted to Gas Turbines, Steam Turbines, associated plant equipment and related utilities. QUALIFICATIONS & SKILLS:Minimum Qualifications:Higher Secondary School Certificate. Minimum Experience:4 years in a power station.2 years’ work experience as Desalination Operator (PG7) or equivalent experience gained working in a similar industry. Skills:Achieved competencies in all areas except DCR operation. English language skills (to prepare and complete shift reports. Intermediate 3 or equivalent level). Communication Skills. Basic numeracy (e.g. concentration, percentage, unit conversion, rate calculations etc.). Ability to understand single line diagram. IT skills. Problem solving skills. Planning and organising skills. Communication skills. Interpersonal skills Teamwork skills.

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p>Field Operation &amp; maint, Units monitoring performance , NFE/NFS projects, LNG Trains, Helium Plants, Units , Offshore and On Shore Pants/Divisions for Operation &amp; Services. (LNG/NLNG/HELIUM/SULFUR units) Rover /Panel Operator&amp; Supervisors</p></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p><b>Required Candidate profile</b></p><p>Applicant should have Oil &amp; Gas , Sulfur , IR, UTL ,SRU, Storage &amp; loading facilities preferably in working of LNG Rover /Panel Operator&amp; Supervisors in offshore and on shore duties</p><p></p></section>

Job description:<br><br>JOB PURPOSE:To assist the Operator, Cell Relining in the refurbishment of superstructures, cell relining activities such as pot changing, rebuilding pot shell and ensure these are carried out in accordance with standard procedures, safely and efficiently to achieve maximum production. KEY ACCOUNTABILITIES:Assists cell relining operator preparing in advance all necessary tools and equipment required for casting prior to actual operations taking place in a safe and efficient manner. Operates mobile equipment such as forklift, pay loader etc., as required complying with all safety procedures. Assists cell relining operator bricks lining in accordance with required standards and specified designs. Assists in carrying out superstructure refurbishment, welding and fabrication jobs, and capable of performing ramming processes. Maintains a high standard of housekeeping at all times. QUALIFICATIONS & SKILLS:Minimum Qualifications:Completion of training modules specified for PG5 position Minimum Experience:One year of experience in heavy industry is preferable. Skills:Completion of the following courses :Aluminium/Water Explosions Electrical hazards Possession of Forklift Licence Category 7

Job Title: MEP CAD Operator Job Location: Ras Laffan Industry: Oil & Gas Contract: 1 Month Extendable<br>Job Summary:We are looking for an experienced MEP CAD Operator with a minimum of 5 years of relevant experience to prepare, modify, and maintain accurate Mechanical, Electrical, and Plumbing (MEP) drawings for Oil & Gas projects. The role involves producing shop drawings, as-built drawings, and coordination drawings while ensuring compliance with project specifications, industry standards, and client requirements. The ideal candidate should have strong Auto CAD skills and the ability to coordinate effectively with multidisciplinary teams.<br>Mandatory Requirements & Qualifications:Experience:Minimum 5 years of experience as an MEP CAD Operator. Oil & Gas project experience is mandatory. Experience on Qatar Energy, Ras Laffan, or other major Oil & Gas projects is preferred. Education:Diploma or Bachelor's Degree in Mechanical Engineering, Electrical Engineering, Drafting, or a related discipline. Technical Skills:Proficiency in Auto CAD (Mandatory). Experience preparing MEP shop drawings, fabrication drawings, coordination drawings, and as-built drawings. Good knowledge of HVAC, Plumbing, Fire Fighting, and Electrical systems. Understanding of P&IDs, equipment layouts, and utility drawings. Knowledge of Autodesk Navisworks or Revit MEP is an added advantage. Mandatory Criteria:Minimum 5 years of MEP CAD drafting experience. Oil & Gas project experience is mandatory. Strong knowledge of international codes and project standards. Ability to coordinate with Mechanical, Electrical, Civil, and Structural teams. Excellent communication skills and attention to detail.<br>Key Responsibilities:Prepare and update MEP shop drawings, fabrication drawings, coordination drawings, and as-built drawings using Auto CAD. Coordinate with multidisciplinary engineering teams to resolve drawing conflicts and ensure compliance with project specifications and applicable codes. Maintain drawing revisions, document control, material layouts, and provide drafting support throughout project execution.

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <strong>Primary Purpose of the Job</strong><br><p>• Requires high‑level judgment to support supervisory decisions.<br>• Coordinates across multiple units under tight timelines.<br>• Exposure to toxic gases, high temperatures, and emergency conditions.<br>• Works 12‑hour rotating shifts including nights and holidays.<br>• Maintains continuous situational awareness across shift roles.</p><br> <br><strong>Required Experience and Skills</strong><br><p>• 8 years refinery/chemical plant operations experience.<br>• 3 years as Senior Operator or equivalent.</p><br> <br><strong>Educational Qualifications</strong><br><p>• Higher Secondary Certificate or equivalent.<br>• HNC/Technical Diploma in Chemical/Process Engineering preferred.</p><br> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <strong>Primary Purpose of the Job</strong><br><p>• Requires high‑level judgment to support supervisory decisions.<br>• Coordinates across multiple units under tight timelines.<br>• Exposure to toxic gases, high temperatures, and emergency conditions.<br>• Works 12‑hour rotating shifts including nights and holidays.<br>• Maintains continuous situational awareness across shift roles.</p><br> <br><strong>Required Experience and Skills</strong><br><p>• 8 years refinery/chemical plant operations experience.<br>• 3 years as Senior Operator or equivalent.</p><br> <br><strong>Educational Qualifications</strong><br><p>• Higher Secondary Certificate or equivalent.<br>• HNC/Technical Diploma in Chemical/Process Engineering preferred.</p><br> </div>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p><b>Department</b><br><br>OPERATIONS - REFINING<br><br><b>Primary Purpose of the Job</b><br><br> Requires high-level judgment to support supervisory decisions.<br> Coordinates across multiple units under tight timelines.<br> Exposure to toxic gases, high temperatures, and emergency conditions.<br> Works 12-hour rotating shifts including nights and holidays.<br> Maintains continuous situational awareness across shift roles.<br><br><b>Required Experience and Skills</b><br><br> 8 years refinery/chemical plant operations experience.<br> 3 years as Senior Operator or equivalent.<br><br><b>Educational Qualifications</b><br><br> Higher Secondary Certificate or equivalent.<br> HNC/Technical Diploma in Chemical/Process Engineering preferred.</p></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p> Requirements &amp; Summary /li&gt; Company Details /li&gt; </p><p></p></section>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <strong>Primary Purpose of the Job</strong><br><p>• Requires high‑level judgment to support supervisory decisions.<br>• Coordinates across multiple units under tight timelines.<br>• Exposure to toxic gases, high temperatures, and emergency conditions.<br>• Works 12‑hour rotating shifts including nights and holidays.<br>• Maintains continuous situational awareness across shift roles.</p><br> <br><strong>Required Experience and Skills</strong><br><p>Minimum Experience:<br>• 8 years refinery/chemical plant operations experience.<br>• 3 years as Senior Operator or equivalent.<br></p><br> <br><strong>Educational Qualifications</strong><br><p>• Higher Secondary Certificate or equivalent.<br>• HNC/Technical Diploma in Chemical/Process Engineering preferred.<br></p><br> </div>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p>We are seeking to meet and hire talented professionals from South America for exciting upcoming opportunities to support our operations in Qatar. Register your interest today for a chance to join our diverse community of experts.</p><p>Perform the field operation of assigned facilities/units relevant to your experience which could be Utility, Inlet Receiving, Sulphur Recovery and LNG, by monitoring performance and condition of equipment and maintaining the processes within operable limits as defined in standard procedures and instructions to achieve safe and reliable plant operation.</p><p>Maintain the competency of all operational procedures and practices through on-the-job training and job rotation to ensure readiness and capability to assume the operator role. Operate field equipment in accordance with operating and approved safety procedures to ensure effective process flows and optimum operational status of equipment. Monitor and log all operating parameters ensuring that all irregularities are reported to immediate supervisor for advice and/or resolution. Prepare field equipment in allocated work area for maintenance activities and follow-up execution and recommission equipment upon satisfactory completion of work. Ensure all Permit to Work requirements and expectations throughout Permit to Work issuance in the field and during PTW field audits.</p><p>Monitor all personnel and activities on site using, but limited to, unit surveillance, regular safety walks, audits and Observation Cards to ensure site safety and operational effectiveness. Provide immediate first-line response capability in the event of emergencies or major incidents to eliminate or limit potential loss or damage to Company personnel, assets or the environment. Ensure incoming shift operator is fully briefed on current operating status and significant events during previous shift to ensure seamless hand-over of responsibilities. Collect all regular and special samples correctly as per schedule and direction of shift supervisor. Perform electrical isolation and de-isolation work of low voltage electrical equipment in preparation of equipment for maintenance activities in line with approved procedure.</p></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p>Completion of Secondary School Education (12 years) and a Vocational Training Programme Certificate.</p><p>5 years operator experience within Utility, Inlet Receiving, Sulphur Recovery or LNG facility.</p><p></p></section>

The Talent Engine of Middle East is HIRING????!<br>DCS Board Operator<br>Key Responsibilities* Operate and monitor the DCS during pre-commissioning, commissioning, and startup activities, including loop checks, functional testing, SAT, and system verification.* Coordinate with field technicians, ICSS vendors, and Mechanical, Electrical, and Piping teams to execute loop testing, resolve system issues, and support field commissioning activities.* Verify and update engineering documents, including Instrument Loop Diagrams (ILDs), Alarm Objective Analysis (AOA), datasheets, control logic and commissioning records to ensure accuracy.* Monitor, test, and validate alarms, control loops, software and hardware modifications, while identifying, troubleshooting and reporting operational issues to supervisors.* Ensure compliance with company SHES requirements, permit-to-work procedures, and maintain accurate progress reports, loop folders, and commissioning documentation.<br>Qualifications* Must have a Degree or Diploma in Instrumentation, Electrical, Electronics, Control Engineering* Must have a minimum of 6 years' experience in the Oil & Gas industry , preferably as a DCS/Board Operator or Commissioning Operator.* Strong knowledge of Distributed Control Systems (DCS), PLCs, HMI operations, and ICSS systems.* Experience in commissioning activities including loop checks, functional testing, alarm testing and plant startup support.* Strong understanding of safety procedures and permit-to-work systems.<br>If you meet the above criteria, please send your Updated CV & Certificates to:???? Email: kisivuli@madre-me.com | resumes@madre-me.zohorecruitmail.com ‬‬???? Mobile/Whats App : +974 31171747

The Talent Engine of Middle East is HIRING????!<br>DCS Board Operator<br>Key Responsibilities* Operate and monitor the DCS during pre-commissioning, commissioning, and startup activities, including loop checks, functional testing, SAT, and system verification.* Coordinate with field technicians, ICSS vendors, and Mechanical, Electrical, and Piping teams to execute loop testing, resolve system issues, and support field commissioning activities.* Verify and update engineering documents, including Instrument Loop Diagrams (ILDs), Alarm Objective Analysis (AOA), datasheets, control logic and commissioning records to ensure accuracy.* Monitor, test, and validate alarms, control loops, software and hardware modifications, while identifying, troubleshooting and reporting operational issues to supervisors.* Ensure compliance with company SHES requirements, permit-to-work procedures, and maintain accurate progress reports, loop folders, and commissioning documentation.<br>Qualifications* Must have a Degree or Diploma in Instrumentation, Electrical, Electronics, Control Engineering* Must have a minimum of 6 years' experience in the Oil & Gas industry , preferably as a DCS/Board Operator or Commissioning Operator.* Strong knowledge of Distributed Control Systems (DCS), PLCs, HMI operations, and ICSS systems.* Experience in commissioning activities including loop checks, functional testing, alarm testing and plant startup support.* Strong understanding of safety procedures and permit-to-work systems.<br>If you meet the above criteria, please send your Updated CV & Certificates to:???? Email: kisivuli@madre-me.com | resumes@madre-me.zohorecruitmail.com ‬‬???? Mobile/Whats App : +974 31171747

The Talent Engine of Middle East is HIRING????!<br>DCS Board Operator<br>Key Responsibilities* Operate and monitor the DCS during pre-commissioning, commissioning, and startup activities, including loop checks, functional testing, SAT, and system verification.* Coordinate with field technicians, ICSS vendors, and Mechanical, Electrical, and Piping teams to execute loop testing, resolve system issues, and support field commissioning activities.* Verify and update engineering documents, including Instrument Loop Diagrams (ILDs), Alarm Objective Analysis (AOA), datasheets, control logic and commissioning records to ensure accuracy.* Monitor, test, and validate alarms, control loops, software and hardware modifications, while identifying, troubleshooting and reporting operational issues to supervisors.* Ensure compliance with company SHES requirements, permit-to-work procedures, and maintain accurate progress reports, loop folders, and commissioning documentation.<br>Qualifications* Must have a Degree or Diploma in Instrumentation, Electrical, Electronics, Control Engineering* Must have a minimum of 6 years' experience in the Oil & Gas industry , preferably as a DCS/Board Operator or Commissioning Operator.* Strong knowledge of Distributed Control Systems (DCS), PLCs, HMI operations, and ICSS systems.* Experience in commissioning activities including loop checks, functional testing, alarm testing and plant startup support.* Strong understanding of safety procedures and permit-to-work systems.<br>If you meet the above criteria, please send your Updated CV & Certificates to:???? Email: kisivuli@madre-me.com | resumes@madre-me.zohorecruitmail.com ‬‬???? Mobile/Whats App : +974 31171747

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p><b>Position:</b></p> <div>Field Operator - (2)</div> <div><b>Date Open:</b></div> <div>Feb 19, 2026 </div> <div><b>Closing Date:</b></div> <div>May 31, 2026 </div> <div><b>Principal:</b></div> <div>Qatar District Cooling Company </div> <div><b>Country:</b></div> <div>Doha, Qatar </div> <div><b>Additional Qualifications:</b></div> <p><strong>Safety Observation</strong></p> <ul> <li> Raise SO in CMMS when found during shift.</li> </ul> <p><strong>Security Rounds:</strong></p> <ul> <li> Conduct regular security rounds of the plant, checking for unauthorized personnel or security breaches (this is part of normal structured round check).</li> </ul> <p><strong>Safety Check:</strong></p> <ul> <li> Conduct a thorough safety inspection of the assigned area, including equipment, PPE, and emergency exits.</li> <li> Ensure all safety signage is visible and up-to-date.</li> </ul> <p><strong>Emergency Response</strong></p> <ul> <li> Respond to emergencies, such as equipment failures, fires, or spills.</li> </ul> <p><strong>PTW System</strong></p> <ul> <li> Issuing, reviewing, or verifying the Permit-to-Work (PTW) system for maintenance and operational activities.</li> </ul> <p><strong>Equipment Line Up / LOTO</strong></p> <ul> <li> Perform LOTO, changeover or shutdown equipment. Isolate equipment for handover to maintenance.</li> </ul> <p><strong>Equipment Inspection:</strong></p> <ul> <li> Visually inspect critical equipment (pumps, valves, chillers, etc.) for any signs of damage, leaks, or abnormal operation.</li> <li> Check lubrication levels and perform routine lubrication as needed.</li> </ul> <p><strong>Parameter Monitoring:</strong></p> <ul> <li>Monitor key process parameters (pressure, temperature, flow rate, etc.)</li> </ul> <p><strong>System Startup:</strong></p> <ul> <li> Initiate the startup procedure for assigned systems, following established checklists and procedures.</li> </ul> <p><strong>System Shutdown:</strong></p> <ul> <li> If required, initiate the shutdown procedure for assigned systems, following established checklists and procedures.</li> </ul> <p><strong>Alarm &amp; Event (A&amp;E) Analysis</strong></p> <ul> <li> Refer to alarm screen at the equipment panel. Monitor and raise info to CCC Operators for any anomalies.</li> </ul> <p><strong>Shift Handover:</strong></p> <ul> <li> Prepare a detailed shift handover report, including any ongoing issues, maintenance requirements, and abnormal events.</li> <li> Conduct a handover "shake-hand" handover meeting to ensure proper baton passing.</li> </ul> <p><strong>Plant Optimization</strong></p> <ul> <li> Work on optimizing plant performance by analyzing system data and making minor adjustments to improve efficiency or reduce energy consumption. Coordination with CCC Operators.</li> </ul> <p><strong>Troubleshooting and Maintenance:</strong></p> <ul> <li> Respond to any alarms or alerts and take necessary corrective actions.</li> <li> Perform scheduled maintenance tasks, such as cleaning filters, replacing gaskets, or tightening bolts.</li> <li> Identify and troubleshoot minor equipment issues, such as valve leaks or pump vibrations.</li> </ul> <p><strong>Defect Management</strong></p> <ul> <li> Raise SR (or relay the info to CCC Operator in charge) in CMMS according to the right priority.</li> </ul> <p><strong>Monitoring of Chemical Treatment Systems</strong></p> <ul> <li> Ensure that the water treatment system is operating correctly, monitoring chemical levels, and ensuring that water quality parameters are within specified limits.</li> </ul> <p><strong>Others and Extras</strong></p> <ul> <li> Provide information and update from the field to CCC Operator to maintain accurate and up-to-date records in the Daily Operation Report (DOR).</li> <li> Occasionally attend site visits by visitors or contractors.</li> <li> Perform any other duty as assigned by the Plant Operations Supervisor</li> </ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p>Candidates must have at least <b>Vocational Diploma / Short Course Certificate</b><br> The job requires <b>Male</b> applicants.<br> Minimum of <b>5</b> years working experience is required for this position<br></p><p></p></section>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p><b>Position:</b></p> <p>Field Operator - (2)</p> <p><b>Date Open:</b></p> <p>Feb 19, 2026</p> <p><b>Closing Date:</b></p> <p>May 31, 2026</p> <p><b>Principal:</b></p> <p>Qatar District Cooling Company</p> <p><b>Country:</b></p> <p>Doha, Qatar</p> <p><b>Additional Qualifications:</b></p> <p><strong>Safety Observation</strong></p> <ul> <li>Raise SO in CMMS when found during shift.</li> </ul> <p><strong>Security Rounds:</strong></p> <ul> <li>Conduct regular security rounds of the plant, checking for unauthorized personnel or security breaches (this is part of normal structured round check).</li> </ul> <p><strong>Safety Check:</strong></p> <ul> <li>Conduct a thorough safety inspection of the assigned area, including equipment, PPE, and emergency exits.</li> <li>Ensure all safety signage is visible and up-to-date.</li> </ul> <p><strong>Emergency Response</strong></p> <ul> <li>Respond to emergencies, such as equipment failures, fires, or spills.</li> </ul> <p><strong>PTW System</strong></p> <ul> <li>Issuing, reviewing, or verifying the Permit-to-Work (PTW) system for maintenance and operational activities.</li> </ul> <p><strong>Equipment Line Up / LOTO</strong></p> <ul> <li>Perform LOTO, changeover or shutdown equipment. Isolate equipment for handover to maintenance.</li> </ul> <p><strong>Equipment Inspection:</strong></p> <ul> <li>Visually inspect critical equipment (pumps, valves, chillers, etc.) for any signs of damage, leaks, or abnormal operation.</li> <li>Check lubrication levels and perform routine lubrication as needed.</li> </ul> <p><strong>Parameter Monitoring:</strong></p> <ul> <li>Monitor key process parameters (pressure, temperature, flow rate, etc.)</li> </ul> <p><strong>System Startup:</strong></p> <ul> <li>Initiate the startup procedure for assigned systems, following established checklists and procedures.</li> </ul> <p><strong>System Shutdown:</strong></p> <ul> <li>If required, initiate the shutdown procedure for assigned systems, following established checklists and procedures.</li> </ul> <p><strong>Alarm &amp; Event (A&amp;E) Analysis</strong></p> <ul> <li>Refer to alarm screen at the equipment panel. Monitor and raise info to CCC Operators for any anomalies.</li> </ul> <p><strong>Shift Handover:</strong></p> <ul> <li>Prepare a detailed shift handover report, including any ongoing issues, maintenance requirements, and abnormal events.</li> <li>Conduct a handover "shake-hand" handover meeting to ensure proper baton passing.</li> </ul> <p><strong>Plant Optimization</strong></p> <ul> <li> Work on optimizing plant performance by analyzing system data and making minor adjustments to improve efficiency or reduce energy consumption. Coordination with CCC Operators.</li> </ul> <p><strong>Troubleshooting and Maintenance:</strong></p> <ul> <li>Respond to any alarms or alerts and take necessary corrective actions.</li> <li>Perform scheduled maintenance tasks, such as cleaning filters, replacing gaskets, or tightening bolts.</li> <li> Identify and troubleshoot minor equipment issues, such as valve leaks or pump vibrations.</li> </ul> <p><strong>Defect Management</strong></p> <ul> <li>Raise SR (or relay the info to CCC Operator in charge) in CMMS according to the right priority.</li> </ul> <p><strong>Monitoring of Chemical Treatment Systems</strong></p> <ul> <li>Ensure that the water treatment system is operating correctly, monitoring chemical levels, and ensuring that water quality parameters are within specified limits.</li> </ul> <p><strong>Others and Extras</strong></p> <ul> <li>Provide information and update from the field to CCC Operator to maintain accurate and up-to-date records in the Daily Operation Report (DOR).</li> <li>Occasionally attend site visits by visitors or contractors.</li> <li>Perform any other duty as assigned by the Plant Operations Supervisor</li> </ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p>Candidates must have at least <b>Vocational Diploma / Short Course Certificate</b></p> <p>The job requires <b>Male</b> applicants.</p> <p>Minimum of <b>5</b> years working experience is required for this position</p><p></p></section>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p><b>Position:</b></p> <div> Field Operator - (2)<br></div> <div> <b>Date Open:</b> </div> <div> Feb 19, 2026 </div> <div> <b>Closing Date:</b> </div> <div> May 19, 2026 </div> <div> <b>Principal:</b> </div> <div> Qatar District Cooling Company </div> <div> <b>Country:</b> </div> <div> Doha, Qatar </div> <div> <b>Additional Qualifications:</b> </div> <div> <p><strong>Safety Observation</strong></p> <ul> <li> Raise SO in CMMS when found during shift.</li> </ul> <p><strong>Security Rounds:</strong></p> <ul> <li> Conduct regular security rounds of the plant, checking for unauthorized personnel or security breaches (this is part of normal structured round check).</li> </ul> <p><strong>Safety Check:</strong></p> <ul> <li> Conduct a thorough safety inspection of the assigned area, including equipment, PPE, and emergency exits.</li> <li> Ensure all safety signage is visible and up-to-date.</li> </ul> <p><strong>Emergency Response</strong></p> <ul> <li> Respond to emergencies, such as equipment failures, fires, or spills.</li> </ul> <p><strong>PTW System</strong></p> <ul> <li> Issuing, reviewing, or verifying the Permit-to-Work (PTW) system for maintenance and operational activities.</li> </ul> <p><strong>Equipment Line Up / LOTO</strong></p> <ul> <li> Perform LOTO, changeover or shutdown equipment. Isolate equipment for handover to maintenance.</li> </ul> <p><strong>Equipment Inspection:</strong></p> <ul> <li> Visually inspect critical equipment (pumps, valves, chillers, etc.) for any signs of damage, leaks, or abnormal operation.</li> <li> Check lubrication levels and perform routine lubrication as needed.</li> </ul> <p><strong>Parameter Monitoring:</strong></p> <ul> <li>Monitor key process parameters (pressure, temperature, flow rate, etc.)</li> </ul> <p><strong>System Startup:</strong></p> <ul> <li> Initiate the startup procedure for assigned systems, following established checklists and procedures.</li> </ul> <p><strong>System Shutdown:</strong></p> <ul> <li> If required, initiate the shutdown procedure for assigned systems, following established checklists and procedures.</li> </ul> <p><strong>Alarm &amp; Event (A&amp;E) Analysis</strong></p> <ul> <li> Refer to alarm screen at the equipment panel. Monitor and raise info to CCC Operators for any anomalies.</li> </ul> <p><strong>Shift Handover:</strong></p> <ul> <li> Prepare a detailed shift handover report, including any ongoing issues, maintenance requirements, and abnormal events.</li> <li> Conduct a handover "shake-hand" handover meeting to ensure proper baton passing.</li> </ul> <p><strong>Plant Optimization</strong></p> <ul> <li> Work on optimizing plant performance by analyzing system data and making minor adjustments to improve efficiency or reduce energy consumption. Coordination with CCC Operators.</li> </ul> <p><strong>Troubleshooting and Maintenance:</strong></p> <ul> <li> Respond to any alarms or alerts and take necessary corrective actions.</li> <li> Perform scheduled maintenance tasks, such as cleaning filters, replacing gaskets, or tightening bolts.</li> <li> Identify and troubleshoot minor equipment issues, such as valve leaks or pump vibrations.</li> </ul> <p><strong>Defect Management</strong></p> <ul> <li> Raise SR (or relay the info to CCC Operator in charge) in CMMS according to the right priority.</li> </ul> <p><strong>Monitoring of Chemical Treatment Systems</strong></p> <ul> <li> Ensure that the water treatment system is operating correctly, monitoring chemical levels, and ensuring that water quality parameters are within specified limits.</li> </ul> <p><strong>Others and Extras</strong></p> <ul> <li> Provide information and update from the field to CCC Operator to maintain accurate and up-to-date records in the Daily Operation Report (DOR).</li> <li> Occasionally attend site visits by visitors or contractors.</li> <li> Perform any other duty as assigned by the Plant Operations Supervisor</li> </ul> </div></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p>Candidates must have at least <b>Vocational Diploma / Short Course Certificate</b></p> <p>The job requires <b>Male</b> applicants.</p> <p>Minimum of <b>5</b> years working experience is required for this position</p><p></p></section>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p><b>Position:</b></p> <div>Field Operator - (2)</div> <div><b>Date Open:</b></div> <div>Feb 19, 2026 </div> <div><b>Closing Date:</b></div> <div>May 19, 2026 </div> <div><b>Principal:</b></div> <div>Qatar District Cooling Company </div> <div><b>Country:</b></div> <div>Doha, Qatar </div> <div><b>Additional Qualifications:</b></div> <p><b>Safety Observation</b></p> <ul><li>Raise SO in CMMS when found during shift.</li></ul> <p><b>Security Rounds:</b></p> <ul><li>Conduct regular security rounds of the plant, checking for unauthorized personnel or security breaches (this is part of normal structured round check).</li></ul> <p><b>Safety Check:</b></p> <ul><li>Conduct a thorough safety inspection of the assigned area, including equipment, PPE, and emergency exits.</li><li>Ensure all safety signage is visible and up-to-date.</li></ul> <p><b>Emergency Response</b></p> <ul><li>Respond to emergencies, such as equipment failures, fires, or spills.</li></ul> <p><b>PTW System</b></p> <ul><li>Issuing, reviewing, or verifying the Permit-to-Work (PTW) system for maintenance and operational activities.</li></ul> <p><b>Equipment Line Up / LOTO</b></p> <ul><li>Perform LOTO, changeover or shutdown equipment. Isolate equipment for handover to maintenance.</li></ul> <p><b>Equipment Inspection:</b></p> <ul><li>Visually inspect critical equipment (pumps, valves, chillers, etc.) for any signs of damage, leaks, or abnormal operation.</li><li>Check lubrication levels and perform routine lubrication as needed.</li></ul> <p><b>Parameter Monitoring:</b></p> <ul><li>Monitor key process parameters (pressure, temperature, flow rate, etc.)</li></ul> <p><b>System Startup:</b></p> <ul><li>Initiate the startup procedure for assigned systems, following established checklists and procedures.</li></ul> <p><b>System Shutdown:</b></p> <ul><li>If required, initiate the shutdown procedure for assigned systems, following established checklists and procedures.</li></ul> <p><b>Alarm &amp; Event (A&amp;E) Analysis</b></p> <ul><li>Refer to alarm screen at the equipment panel. Monitor and raise info to CCC Operators for any anomalies.</li></ul> <p><b>Shift Handover:</b></p> <ul><li>Prepare a detailed shift handover report, including any ongoing issues, maintenance requirements, and abnormal events.</li><li>Conduct a handover "shake-hand" handover meeting to ensure proper baton passing.</li></ul> <p><b>Plant Optimization</b></p> <ul><li> Work on optimizing plant performance by analyzing system data and making minor adjustments to improve efficiency or reduce energy consumption. Coordination with CCC Operators.</li></ul> <p><b>Troubleshooting and Maintenance:</b></p> <ul><li>Respond to any alarms or alerts and take necessary corrective actions.</li><li>Perform scheduled maintenance tasks, such as cleaning filters, replacing gaskets, or tightening bolts.</li><li> Identify and troubleshoot minor equipment issues, such as valve leaks or pump vibrations.</li></ul> <p><b>Defect Management</b></p> <ul><li>Raise SR (or relay the info to CCC Operator in charge) in CMMS according to the right priority.</li></ul> <p><b>Monitoring of Chemical Treatment Systems</b></p> <ul><li>Ensure that the water treatment system is operating correctly, monitoring chemical levels, and ensuring that water quality parameters are within specified limits.</li></ul> <p><b>Others and Extras</b></p> <ul><li>Provide information and update from the field to CCC Operator to maintain accurate and up-to-date records in the Daily Operation Report (DOR).</li><li>Occasionally attend site visits by visitors or contractors.</li><li>Perform any other duty as assigned by the Plant Operations Supervisor</li></ul></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><p>Candidates must have at least <b>Vocational Diploma / Short Course Certificate</b><br> The job requires <b>Male</b> applicants.<br> Minimum of <b>5</b> years working experience is required for this position<br></p><p></p></section>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <strong>Primary Purpose of the Job</strong><br><p>• Requires high‑level judgment to support supervisory decisions.<br>• Coordinates across multiple units under tight timelines.<br>• Exposure to toxic gases, high temperatures, and emergency conditions.<br>• Works 12‑hour rotating shifts including nights and holidays.<br>• Maintains continuous situational awareness across shift roles.</p><br> <br><strong>Required Experience and Skills</strong><br><p>• 8 years refinery/chemical plant operations experience.<br>• 3 years as Senior Operator or equivalent.</p><br><p>• Strong panel operation and troubleshooting capability.<br>• Ability to read and integrate multiple shift logs and datasets.<br>• Ability to act in supervisory capacity when delegated.<br>• High safety awareness and compliance discipline.<br>• Strong communication and coordination skills. Good oral and reading knowledge of English.<br>• Competent with APC, RIS, LIMS, DCS, SAP.<br>• Certified in Firefighting, First Aid, BA/H₂S.</p><br> <br><strong>Educational Qualifications</strong><br><p>• Higher Secondary Certificate or equivalent.<br>• HNC/Technical Diploma in Chemical/Process Engineering preferred.</p><br> </div>

Job Title: Auto CAD Operator cum Document Controller (Electrical – LV & MV Switchgear) Job Location: Doha<br>Job Summary:We are seeking an experienced Auto CAD Operator cum Document Controller to support LV & MV Switchgear projects. The successful candidate will be responsible for preparing and revising electrical drawings, maintaining engineering documentation, controlling document revisions, and ensuring timely distribution of technical documents in accordance with project specifications and company standards.<br>Mandatory Requirements & Qualifications:Experience:Minimum 5 years of experience in Electrical Auto CAD drafting and document control. Experience in LV & MV Switchgear projects is highly preferred. Education:Diploma or Bachelor's Degree in Electrical Engineering or a related discipline. Auto CAD Certification (Auto CAD Electrical preferred). Technical Skills:Proficiency in Auto CAD. Experience preparing:Single Line Diagrams (SLD) Wiring Diagrams Schematic & Control Diagrams Panel Layouts Termination Drawings Knowledge of Auto CAD Electrical and EPLAN is an added advantage. Familiarity with document control systems, revision management, and engineering documentation workflows.<br>Mandatory Criteria:Strong understanding of electrical schematics and switchgear drawings. Experience in document numbering, revision control, and document tracking. Excellent organizational, communication, and coordination skills. High attention to detail and ability to meet project deadlines.<br>Key Responsibilities:Prepare, modify, and update electrical drawings including SLDs, wiring diagrams, schematics, control diagrams, panel layouts, and termination drawings. Maintain document control processes, revision registers, drawing logs, and engineering documentation while ensuring proper version control and timely document distribution. Coordinate with engineers, project teams, clients, suppliers, and factories to update drawings, resolve technical queries, prepare as-built drawings, and ensure engineering documentation is completed within project timelines.

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p>Position:</p><p>Field Operator - (2)</p><p>Date Open:</p><p>Feb 19, 2026</p><p>Closing Date:</p><p>Jun 30, 2026</p><p>Principal:</p><p>Qatar District Cooling Company</p><p>Country:</p><p>Doha, Qatar</p><p>Qualifications:</p><p>Candidates must have at least Vocational Diploma / Short Course Certificate</p><p>The job requires Male applicants.</p><p>Minimum of 5 years working experience is required for this position</p><p>Additional Qualifications:</p><p>Safety Observation</p><p><br></p><p>·Raise SO in CMMS when found during shift.</p><p>Security Rounds:</p><p><br></p><p>·&nbsp; &nbsp;Conduct regular security rounds of the plant, checking for unauthorized personnel or security breaches (this is part of normal structured round check).</p><p>Safety Check:</p><p><br></p><p>·&nbsp; &nbsp; Conduct a thorough safety inspection of the assigned area, including equipment, PPE, and emergency exits.</p><p>·&nbsp; &nbsp; Ensure all safety signage is visible and up-to-date.</p><p>Emergency Response</p><p><br></p><p>·&nbsp; &nbsp; Respond to emergencies, such as equipment failures, fires, or spills.</p><p>PTW System</p><p><br></p><p>·&nbsp; &nbsp; Issuing, reviewing, or verifying the Permit-to-Work (PTW) system for maintenance and operational activities.</p><p>Equipment Line Up / LOTO</p><p><br></p><p>·&nbsp; &nbsp; Perform LOTO, changeover or shutdown equipment. Isolate equipment for handover to maintenance.</p><p>Equipment Inspection:</p><p><br></p><p>·&nbsp; &nbsp; &nbsp;Visually inspect critical equipment (pumps, valves, chillers, etc.) for any signs of damage, leaks, or abnormal operation.</p><p>·&nbsp; &nbsp; &nbsp;Check lubrication levels and perform routine lubrication as needed.</p><p>Parameter Monitoring:</p><p><br></p><p>Monitor key process parameters (pressure, temperature, flow rate, etc.)</p><p>System Startup:</p><p><br></p><p>·&nbsp; &nbsp; Initiate the startup procedure for assigned systems, following established checklists and procedures.</p><p>System Shutdown:</p><p><br></p><p>·&nbsp; &nbsp; If required, initiate the shutdown procedure for assigned systems, following established checklists and procedures.</p><p>Alarm &amp; Event (A&amp;E) Analysis</p><p><br></p><p>·&nbsp; &nbsp; Refer to alarm screen at the equipment panel. Monitor and raise info to CCC Operators for any anomalies.</p><p>Shift Handover:</p><p><br></p><p>·&nbsp; &nbsp; Prepare a detailed shift handover report, including any ongoing issues, maintenance requirements, and abnormal events.</p><p>·&nbsp; &nbsp; Conduct a handover "shake-hand" handover meeting to ensure proper baton passing.</p><p>Plant Optimization</p><p><br></p><p>·&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Work on optimizing plant performance by analyzing system data and making minor adjustments to improve efficiency or reduce energy consumption. Coordination with CCC Operators.</p><p>Troubleshooting and Maintenance:</p><p><br></p><p>·&nbsp; &nbsp; &nbsp;Respond to any alarms or alerts and take necessary corrective actions.</p><p>·&nbsp; &nbsp; &nbsp;Perform scheduled maintenance tasks, such as cleaning filters, replacing gaskets, or tightening bolts.</p><p>·&nbsp; &nbsp; &nbsp;Identify and troubleshoot minor equipment issues, such as valve leaks or pump vibrations.</p><p>Defect Management</p><p><br></p><p>·&nbsp; Raise SR (or relay the info to CCC Operator in charge) in CMMS according to the right priority.</p><p>Monitoring of Chemical Treatment Systems</p><p><br></p><p>·&nbsp; &nbsp; Ensure that the water treatment system is operating correctly, monitoring chemical levels, and ensuring that water quality parameters are within specified limits.</p><p>Others and Extras</p><p><br></p><p>·&nbsp; &nbsp; &nbsp;Provide information and update from the field to CCC Operator to maintain accurate and up-to-date records in the Daily Operation Report (DOR).</p><p>·&nbsp; &nbsp; &nbsp;Occasionally attend site visits by visitors or contractors.</p><p>·&nbsp; &nbsp; &nbsp;Perform any other duty as assigned by the Plant Operations Supervisor</p></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><h2><br></h2><p></p></section>

<section><p class="heading jdMain">Job Description</p><p class="heading">Roles &amp; Responsibilities</p><div class="paragraph"><p>Position:</p><p>Field Operator - (2)</p><p>Date Open:</p><p>Feb 19, 2026</p><p>Closing Date:</p><p>Jun 30, 2026</p><p>Principal:</p><p>Qatar District Cooling Company</p><p>Country:</p><p>Doha, Qatar</p><p>Qualifications:</p><p>Candidates must have at least Vocational Diploma / Short Course Certificate</p><p>The job requires Male applicants.</p><p>Minimum of 5 years working experience is required for this position</p><p>Additional Qualifications:</p><p>Safety Observation</p><p><br></p><p>·Raise SO in CMMS when found during shift.</p><p>Security Rounds:</p><p><br></p><p>·&nbsp; &nbsp;Conduct regular security rounds of the plant, checking for unauthorized personnel or security breaches (this is part of normal structured round check).</p><p>Safety Check:</p><p><br></p><p>·&nbsp; &nbsp; Conduct a thorough safety inspection of the assigned area, including equipment, PPE, and emergency exits.</p><p>·&nbsp; &nbsp; Ensure all safety signage is visible and up-to-date.</p><p>Emergency Response</p><p><br></p><p>·&nbsp; &nbsp; Respond to emergencies, such as equipment failures, fires, or spills.</p><p>PTW System</p><p><br></p><p>·&nbsp; &nbsp; Issuing, reviewing, or verifying the Permit-to-Work (PTW) system for maintenance and operational activities.</p><p>Equipment Line Up / LOTO</p><p><br></p><p>·&nbsp; &nbsp; Perform LOTO, changeover or shutdown equipment. Isolate equipment for handover to maintenance.</p><p>Equipment Inspection:</p><p><br></p><p>·&nbsp; &nbsp; &nbsp;Visually inspect critical equipment (pumps, valves, chillers, etc.) for any signs of damage, leaks, or abnormal operation.</p><p>·&nbsp; &nbsp; &nbsp;Check lubrication levels and perform routine lubrication as needed.</p><p>Parameter Monitoring:</p><p><br></p><p>Monitor key process parameters (pressure, temperature, flow rate, etc.)</p><p>System Startup:</p><p><br></p><p>·&nbsp; &nbsp; Initiate the startup procedure for assigned systems, following established checklists and procedures.</p><p>System Shutdown:</p><p><br></p><p>·&nbsp; &nbsp; If required, initiate the shutdown procedure for assigned systems, following established checklists and procedures.</p><p>Alarm &amp; Event (A&amp;E) Analysis</p><p><br></p><p>·&nbsp; &nbsp; Refer to alarm screen at the equipment panel. Monitor and raise info to CCC Operators for any anomalies.</p><p>Shift Handover:</p><p><br></p><p>·&nbsp; &nbsp; Prepare a detailed shift handover report, including any ongoing issues, maintenance requirements, and abnormal events.</p><p>·&nbsp; &nbsp; Conduct a handover "shake-hand" handover meeting to ensure proper baton passing.</p><p>Plant Optimization</p><p><br></p><p>·&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Work on optimizing plant performance by analyzing system data and making minor adjustments to improve efficiency or reduce energy consumption. Coordination with CCC Operators.</p><p>Troubleshooting and Maintenance:</p><p><br></p><p>·&nbsp; &nbsp; &nbsp;Respond to any alarms or alerts and take necessary corrective actions.</p><p>·&nbsp; &nbsp; &nbsp;Perform scheduled maintenance tasks, such as cleaning filters, replacing gaskets, or tightening bolts.</p><p>·&nbsp; &nbsp; &nbsp;Identify and troubleshoot minor equipment issues, such as valve leaks or pump vibrations.</p><p>Defect Management</p><p><br></p><p>·&nbsp; Raise SR (or relay the info to CCC Operator in charge) in CMMS according to the right priority.</p><p>Monitoring of Chemical Treatment Systems</p><p><br></p><p>·&nbsp; &nbsp; Ensure that the water treatment system is operating correctly, monitoring chemical levels, and ensuring that water quality parameters are within specified limits.</p><p>Others and Extras</p><p><br></p><p>·&nbsp; &nbsp; &nbsp;Provide information and update from the field to CCC Operator to maintain accurate and up-to-date records in the Daily Operation Report (DOR).</p><p>·&nbsp; &nbsp; &nbsp;Occasionally attend site visits by visitors or contractors.</p><p>·&nbsp; &nbsp; &nbsp;Perform any other duty as assigned by the Plant Operations Supervisor</p></div></section><section><p class="heading">Desired Candidate Profile</p><p class="paragraph"></p><ul><li>Candidates must have at least Vocational Diploma / Short Course Certificate</li></ul><p></p></section>