Reports to: QC Manager
Category: FTE
Unit / Division / Department / Section: QC
Location: Qatar
_______
Job Purpose
Responsible for ensuring that all the Pipes and Couplers are manufactured to the quality standards laid down and that every item is inspected and stamped QC OK when ready for release to the Final Warehouse
Key Accountabilities
Policies & Procedures
- Comply with operational procedures and instructions when performing all job tasks and activities
In-process inspection
- Ensure only approved and QC accepted raw materials are used in the manufacturing process
- Ensure that the production process comply with the technical Know-How documents & Quality Assurance Procedures
- Conduct the refractive index check of the epoxy resin/hardener mix ratio to ensure it meets the set requirements
- Check and monitor the ambient temperature and humidity
- Witness the production processes and ensure that the relevant approved Raw Material Calculation and Machine Set ups are followed to meet the project requirements
- Inform the non-conformances immediately to the responsible Machine Captains and other employees in the Production and QC departments so corrective actions can be taken
Online / Offline Inspection of Pipes and Couplers
- Inspect the Pipes and Couplers as per the requirements of product drawings following the inspection and testing program
- Select QC samples during the production process as per the inspection program and/or project ITPs as applicable
Trading materials inspection
- Inspect the products purchased from the other manufacturing units or sub supplier and ensure that those products meet the project specification requirements and release them for delivery
- Inspect the locking strips, different types of gaskets such as Kroll and Ziller, O-rings, flat gaskets in order to ensure the quality meets the minimum specified requirements
Non-destructive testing
- Conduct the non-destructive tests as per the ITP requirement
- Witness the routine hydro tests for the Pipes and Couplers
Destructive Testing
- Conduct the destructive tests in accordance to the ITP requirements and project commitments agreed with the Client/consultant
- Witness and monitor the short term and medium term survival tests periodically and ensure the tests are not affected with any climatic effects and successfully completed as per the project requirements
Preparation of reports, TPI inspection and release
- Prepare the daily QC internal reports as well as project specific documentation (Manufacturing Record Book - MRB) to be submitted to the Client
- Carry out the final inspection and release together with the Customer TPIs and Client TPIs for all the products comes under the major projects based on the project specific requirements. Also perform additional tests as per the ITP for the witness point of Customer/Client
Stock counting
- Participate and lead a small team of employees during the Half- yearly and Yearly stock counts to ensure that the physical inventory matches the ERP system inventory
- Carry out monthly stock counting for the major raw materials in the stores warehouse and provide the actual data to the QC Engineer for monthly RM stock count report
Mould & Socket Sleeve inspection
- Carry out steel mould and socket sleeve inspection either at factory of at supplier’s premises as per the relevant engineering drawings to ensure that those moulds are manufactured as per the given approved drawings
HSE
- Comply with relevant safety, quality and environmental control procedures and instructions
- Use personal protective equipment and safety gear when performing assigned tasks
- Keep operational areas clean and well organized to prevent incidents and accidents
- Report unsafe acts, incidents or safety violations
- Develop a safety culture by ensuring all staff comply with HSE policies and procedures
- Participate in QHSE audits, incident reporting and review of QHSE performances as require
SPAN OF Communication
- Internal: Production, Projects and Delivery Departments
- External: Third Party Inspectors
Job relevant information (BOUNDARIES & DECISION-MAKING AUTHORITY)
- The jobholder has the authority to reject any product that does not meet QC set standards, with the approval of direct manager
Skills
Required Qualifications:
- Technical School Certificate / On Job Training
Preferred Experience:
- At least 2 years of pipe manufacturing experience
- Engineering Degree / Diploma (Civil or Mechanical)
Job-Specific Skills:
- QC inspection and testing of Raw Material and finished products.
- Reading and interpretation of engineering drawings
- Ability to prepare reports
- Ability to use measuring and testing equipment
COMPETENCIES
- Self-motivated
- Teamwork
- Accurate and attentive to details
This job has been sourced from an external job board.
More jobs on https://www.qureos.com/